SELCO Motorized Potentiometer E7800

The Motorized Potentiometer E7800 is typically used as an interface between increase/decrease contacts and a device requiring control/adjustments by an external potentiometer.

The E7800 Motorized Potentiometer

The E7800 Motorised Potentiometer is typically used as an interface between increase/decrease relay contacts (or push buttons) and a device requiring control by an external potentiometer (e.g. the speed trim of an electronic governor).

All three wires of the potentiometer are directly accessible on external connection terminals, thus providing the best possible flexibility for almost any application.

A special version of the E7800 with DC voltage output is also available. The DC output voltage follows the position of the potentiometer. The design of the E7800 ensures that the potentiometer will “remember” its position although supply is lost.

---

Features:

• • Sealed wire wound potentiometer
  • Built-in dust seal
  • Low speed motor for accurate control
  • High drive capability
  • Resistance from 100 to 10 kohm
  • Large size knob for manual control
  • LED indication of turn direction
  • Optional programmable RPM
  • AC or DC supply

MODULE GENSET WOODWARD Easygen-3000XT Series Paralleling Genset Controllers for Diverse Applications

The easYgen-3000XT Series controllers operate gensets of all sizes and applications. These controllers include specifically designed algorithms and logic to start, stop, control, and protect the genset, circuit breaker, and the utility where applicable. This technology allows standardizing on a single, affordable genset controller for distributed power generation applications. These applications can range from single stand-alone emergency backup power to parallel load sharing of multiple gensets in complex, segmented distribution systems with multiple utility feeds and tie breakers.
The easYgen-3000XT Series paralleling genset controllers provide exceptional versatility and value for OEM switchgear builders, generator packagers, and system integrators.
Benefits include:  

High Flexibility and Reduced Efforts for variants at different applications. One devise fits most applications
Saves Cost of additional PLC as logical/analog operations can be handled by the control’s LogicsManager^TM / AnalogManager^TM 
High Robustness against external disturbances ensured by galvanic isolation of the measuring inputs, relay contacts, biasing outputs, and communication interfaces
Simplified Configuration and Commissioning through Ethernet and USB connectivity, on-board documentation and system update function
Drop-In Replacement extends system longevity
Full Mains, Generator, and Engine Protection minimizes additional protection relays in low voltage applications

14 Built-In Languages enable your genset to speak your local language at the touch of a button

DATAKOM D700 WEB BASED ONE SOLUTION FOR ALL GENSET APPLICATIONS

The D-700 is a next generation
synchronizing genset controller
capable of every communication and
functionality.








FUNCTIONALITIES

 Multi genset synch and load share
Mains synchronization
Single genset parallel with mains
AMF unit with uninterrupted transfer
ATS unit with uninterrupted transfer
Remote start controller
Manual start controller
Engine controller
Remote display & control unit

COMMUNICATIONS

Ethernet port (10/100Mb)
GSM-GPRS
Internal GPRS modem (optional)
Embedded web server
Web monitoring
Web programming
Central Monitoring through internet
SMS message sending
E-mail sending
Free PC software: Rainbow Plus
Free Central Monitoring (2 years)
Modbus RTU through RS-485
Modbus TCP/IP
SNMP
USB Host
USB Device
RS-485 port, adjustable baud rate
RS-232
Micro SD card slot
J1939-CANBUS

DEIF Paralleling and Protection Unit, PPU-3

Easy to operate and configure, DEIF’s PPU-3 control and protection unit is an ideal controller for PLC-based power management systems.

Apart from generator protection and synchronisation, the PPU-3 also features regulation modes including load sharing, fixed power, fixed frequency, etc. Serial communication enables easy interfacing with PLCs, SCADA-systems and more, and the unit features all necessary three-phase measuring circuits, displaying all values and alarms on a quality LCD screen.

Turning the PPU-3 into an engine control unit featuring start/stop and protection functionalities, the optional engine interface card also has a separate power supply and an independent microprocessor.

In cases of PPU-3 processor break-downs, the engine interface card will enter into back-up mode and ensure uninterrupted engine supervision.
In cases of shutdown alarms, the engine shuts down automatically, making it a reliable solution for control and supervision of marine gensets.

Additional Operator Panels (AOP) can easily be installed and integrated for further levels of remote control, supervision and status indication. Both displays and panels feature a dimmer function for use on the ship’s bridge.

With a range of additional hardware options available, as well as DEIF’s Multi-line 2:utility software v.3 (USW-3) with programmable logic (M-Logic), you can customise the application to suit your needs exactly: dedicate specific functions or logic conditions to different inputs and outputs and tune all sequences according to your requirements

DATAKOM D 500 THE NEW WEB BASED

FEATURES :
» Ethernet
» GSM-GPRS
» Internal GPRS modem(optional)
» Embedded web server
» Web monitoring
» Web programming
» GSM-SMS
» e -mail
» Free PC software
» Modbus RS-485
» Modbus over IP
» SNMP
» USB Host(optional)
» USB Device
» RS-485
» RS-232(optional)
» Micro SD card slot(optional)
» J1939-CANBUS

DSE3110 MANUAL & AUTO START CONTROL MODULE

KEY FEATURES

• Back-lit icon LCD display
• Front panel editing
• LED and LCD alarm indication
• Power Save mode
• CAN and Magnetic Pick-up/Alt.
versions available (specify on
ordering)
• PC configurable
• 6 Digital inputs
• 4 Outputs (2 configurable on
Magnetic Pick up/Alt., 4
configurable on CAN version)
• Configurable timers and alarms
• Alternative configuration
• Remote Start input
• Generator voltage display
• Generator frequency display
• Battery voltage display
• Engine speed display
• Hours counter
• Engine pre-heat
• Comprehensive shutdown or
warning on fault condition
KEY BENEFITS
• Tamper-proof hours counter
provides accurate information
for monitoring and maintenance
periods
• Multiple engine parameters are
monitored simultaneously
• Module can be configured to
suit individual applications
• Suitable for engine only
applications
• Compatible with a wide range
of CAN engines
• Uses DSE Configuration Suite
PC software for simplified
configuration
• IP65 rating (with optional
gasket) offers increased
resistance to water ingress
• Licence-free PC software
RELATED MATERIALS
TITLE PART NO’S
DSE3110 Installation Instructions 053-050
DSE3110 Quick Start Guide 057-104
DSE3110 Operator Manual 057-086
DSE3110 Configuration Suite PC Software Manual 057-087
SPECIFICATION
DC SUPPLY
CONTINUOUS VOLTAGE RATING
8 V to 35 V Continuous
CRANKING DROPOUTS
Able to survive 0 V for 50 mS, providing
supply was at least 10 V before dropout
and supply recovers to 5 V. This is achieved
without the need for internal batteries
CHARGE FAIL/ EXCITATION
8 V to 35 V fixed power source 2.5 W
NOMINAL STANDBY CURRENT
23 mA at 12 V, 18 mA at 24 V
MAXIMUM OPERATING CURRENT
35 mA at 12 V, 30 mA at 24 V
OUTPUTS
OUTPUT A (FUEL)
2 A DC at supply voltage
OUTPUT B (START)
2 A DC at supply voltage
AUXILIARY OUTPUTS C,D
2 A DC at supply voltage
GENERATOR
VOLTAGE RANGE
15 V - 333 V AC (L-N)
FREQUENCY RANGE
3.5 Hz to 75 Hz
MAGNETIC PICK UP
VOLTAGE RANGE
+/- 0.5 V to 70 V
FREQUENCY RANGE
10,000 Hz (max)
DIMENSIONS
OVERALL
98 mm x 79 mm x 40 mm
3.9” x 3.1” x 1.6”
PANEL CUT-OUT
80 mm x 68 mm
3.1” x 2.7”
MAXIMUM PANEL THICKNESS
8 mm
0.3”
DSE3110
MANUAL & AUTO START CONTROL MODULE
®
DSEGenset
FEATURES
Registered in England & Wales No.01319649
VAT No.316923457
Deep Sea Electronics Plc maintains a policy of continuous development and reserves the right to change
the details shown on this data sheet without prior notice. The contents are intended for guidance only.

DSE4510/20 AUTO START AND AUTO MAINS FAILURE CONTROL MODULES

The DSE4510 Auto Start Control
Module and the DSE4520 Auto
Mains (Utility) Failure Control Module
are suitable for a wide variety of
single gen-set applications.
Whilst maintaining functions included
within higher end controllers, such as
generator or load power monitoring,
the DSE45xx range of especially
compact controllers provide the user
with the ultimate size to feature ratio.
Monitoring engine speed, oil
pressure, coolant temperature,
frequency, voltage, current, power
and fuel level, the modules will give
comprehensive engine and alternator
protection. This will be indicated on
the largest back-lit LCD icon display
in its class via an array of warning,
electrical trip and shutdown alarms.
Electronic J1939 (CAN) and nonelectronic
(alternator sensing) engine
support for diesel, gas and petrol
engines all in one variant. With a
number of flexible inputs, outputs
and protections, the modules can be
easily adapted to suit a wide range of
applications including lighting towers
with the added option for staged
loading outputs.
Through USB Communication both
modules can be easily configured
using the DSE Configuration Suite
PC Software or can be fully
configured through the module's
fascia.
All DSE products are supported by
the DSE global technical support
team which gives our customers and
end users access to 24 hour system
help and advice.